Exactly How to Set up a Tub Yourself
Exactly How to Set up a Tub Yourself
Blog Article
We've uncovered this post about How to Install a Bathtub listed below on the internet and figured it made good sense to discuss it with you on my blog.
Mounting a bath tub isn't specifically brain surgery, yet it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old tub with a new one is likewise a moderately tough job. If the old bathtub is easily easily accessible, the job can move rapidly; if you need to open a wall to eliminate the old tub as well as position the new bathtub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly need a helper to vacate the old bathtub and also embeded in the brand-new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed task, it is far better to take into consideration using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a new bathtub in your washroom if you have actually currently gotten a brand-new bathtub as well as don't need to change the setup of your previous water system pipes.
Your tools and also product checklist should consist of the following:
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, after that the first thing you ought to do is separate the supply of water. After doing so, activate the faucets to drain any kind of water remaining in the system. The procedure of eliminating the existing taps can be rather problematic due to the limited gain access to that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Before going on to fit the new faucets, compare the pipeline connections on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and the sink. Protect the faucet in place with the maker offered backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former type needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Tub
Utilizing the two wooden boards under its feet, put the tub in the needed setting. The wood boards are practical in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and adjusting the feet on the tub up until the level checks out degree.
To mount taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the water supply and also inspect all joints as well as brand-new pipework for leaks as well as tighten them if required. Fill up the tub as well as additionally examine the overflow electrical outlet as well as the typical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling and also securing around the tub ought to wait until the bathtub has been made use of at the very least when as this will settle it right into its last position.
Preparing for the Setup
First of all, the supporting framework supplied with the bathroom must be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the flexible faucet ports to the bottom of both faucets using 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final setting.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface between the bath and also the tiling, bring about problems with wetness and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to allow for the movement experienced when the tub remains in usage. The sealer can crack fairly early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Do you appreciate reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Put feedback down the page. We'd be pleased to see your reactions about this piece. We hope that you visit us again before long. If you enjoyed our blog entry please make sure you remember to pass it around. I appreciate reading our article about Installing A Bathtub.
Pricing
Report this page